![]() ![]() Check if the status LEDs on the Miniserver’s network (LAN) port are blinking or on.Miniserver flashes green, but is not accessible in the network Once this restart is complete, the Miniserver will run with the updated configuration.ĭiagnostics Miniserver is not found in search / Miniserver not accessible in the network Simply click on “Save to Miniserver” and the local changes made in the software will be transferred to the Miniserver and the Miniserver will automatically restart to load the changes. After making changes, you can save them to the Miniserver.To do so, simply click on “Load from Miniserver”. It is recommended to always load the current project, including any user changes, from the Miniserver into Loxone Config before making changes.In this example, we have assigned the address 192.168.1.1 to the computer:Ĭonfirm with OK and a connection with the Miniserver via Loxone Config is possible.Īny changes to the Miniserver configuration after the initial setup, can also be made while the connection to the Miniserver is active.ĭetails on establishing a connection can be found here. Now double-click on “Internet Protocol Version 4”: Then switch to the properties of the Ethernet or LAN connection: Then click on “Change adapter settings” on the left side: To do this, go to the “Network and Sharing Center” in the Control Panel. Therefore, the PC must be assigned an IP address matching the Miniserver in the same address range (192.168.1.x). The Miniserver Gen.1 adopts the default static address 192.168.1.77 if it is not assigned an address by a DHCP server. However, you can still manually assign an IP address to the Miniserver and the computer to enable a connection. In this case, the Miniserver and computer adopt a .x link-local address if both are set to DHCP. Instead, link-local addressing via Zeroconf is supported. ![]() Since version 12.0, the current Miniserver no longer falls back to 192.168.1.77 if no DHCP server is present. Two options are available for this, which differ depending on the Miniserver generation: Current Miniserver This is useful for troubleshooting in order to rule out network related issues. The Miniserver can also be connected directly to a PC via a network cable or switch if no router or DHCP server is available. Disable these temporarily, and try assigning the address again. If this does not work, the connection may have been blocked by a virus scanner or firewall. Then click on Apply and send to Miniserver (You can get the DNS server addresses either from the ISP, or you can search the Internet for alternatives).ĥ. Add the subnet mask, gateway (usually the IP address of the router/modem) and the addresses of the DNS servers. Enter a valid IP address for the Miniserver that is outside of the DHCP range of the router. The MAC address (serial number) of the currently connected Miniserver is used.Ĥ. Then click the button Configure Miniserver in the menu bar, and select the Network tab.ģ. First click on the Miniserver in the Periphery treeĢ. This method is used when you are already connected to the Miniserver:ġ. Change address using Configure Miniserver ![]() ![]() The Miniserver restarts and can then be reached at the new assigned IP address. (You can get the DNS server addresses either from the ISP, or you can search the Internet for alternatives). Enter a valid IP address for the Miniserver that is outside of the DHCP range of the router.You can find it on the label on the back of the device. blank document), then enter the MAC address (serial number) of the Miniserver. The MAC address (serial number) of the Miniserver is copied from the current document.Then click the Configure Device button in the menu bar and select Miniserver as the device.First click on the Miniserver in the Periphery tree.Open the configuration software Loxone Config and follow the steps below: Use this function to establish the connection afterwards. Assigning an IP address via Configure Device is also possible when the Miniserver is in a different IP range and it is not possible to establish a connection. ![]()
0 Comments
Leave a Reply. |